2024 Land Pride RC2512 Series Base

Information

2024 Land Pride RC2512 Series

Land Pride's RC2512 Rotary Cutter is designed for smaller tractors while retaining the features and benefits of larger folding cutters. The 12' width, sharp turning radius, and low tongue weight makes this an ideal Rotary Cutter for compact tractor owners that need a large rotary cutter for light agricultural and municipal grass maintenance.

Features may include:

GEARBOX WARRANTY

5 Year Limited Gearbox Warranty demonstrates our confidence in the gearbox's quality and lasting performance.

1-1/2" CUTTING CAPACITY

These cutters offers 1-1/2" cutting capacity. See Operator's Manual for more information.

ADJUSTABLE JACK ANGLE

Helps keep park jack vertical when in use.

LED SIGNAL LIGHTS

LED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.

BEVELED SKID SHOES

Wing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.

10 GAUGE STUMP JUMPER

Round stump jumper allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.

SPRING CUSHION

Deck-mounted spring cushion provides a smooth ride in rough terrain.

DUAL LEVELING RODS

Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain.

NARROW TONGUE DESIGN

Narrow tongue design handles tight turns - great size for country estates.

Photos

Highlights

  • Jewell, Kansas
  • 2024
  • Land Pride
  • RC2512 Series Base
  • Available
  • Cutting: 1 1/2" to 12" (3.8 cm to 30.5 cm)

Specifications

  • 2024
  • Land Pride
  • RC2512 Series
  • Base
  • Rotary Cutters
  • Tractor horsepower: 40-100 hp (30-75 kW)
  • Gearbox capacity - Splitter: gear lube 80-90W EP / Center & wings: gear lube 80-90W EP
  • Gearbox horsepower Splitter: 160 hp (119 kW) / Center & wings: 100 hp (75 kW) | 6 Spline
  • Input: Category 4 with constant velocity u-joint | Intermediate & wing: Category 3 with slip-clutch
  • 20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires or 21" (53.3 cm) laminated wheels | Number of: 4 - Wheels: 2 on transport axle and one on each wing axle
  • Blade tip At 540 rpm - Center Blades = 16,500 FPM (83.8 mps) / Wing Blades = 16,000 FPM (81.3 mps)
  • LP Performance hitch and swivel hitch
  • Signal: LED / 7 Pin connector: SAE J560 pin configuration
  • Gearbox shafts Input shaft: 1 3/8" (3.5 cm) 6 Spline / Output shaft: 1 1/2" (3.8 cm) | Cutting capacity: 1 1/2" (3.8 cm) | Lift hydraulics: 2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings and stroke control spacers | Wing folding hydraulics: 2" bore x 8" stroke hydraulic cylinders, hoses, and fittings | Wing flex while operating: Max. 20° down, can float up as needed as long as the wheel(s) are still on the ground. | Blades - 6 (2 per deck): 1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift | Blade overlap: 6" (15.2 cm) | Stump jumper / blade holder: 10 Gauge (3.4 mm) round dish shaped pan, reinforced with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar
  • 12'-0" (3.66 m)
  • cutter: 12'-7" (3.84 m)
  • Minimum: 7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground.
  • 13'-3" (4.04 m)
  • 11" (27.9 cm)
  • Cutting: 1 1/2" to 12" (3.8 cm to 30.5 cm)
  • Gearbox capacity - Splitter: 4.5 pints (2.13 L) / Center & wings: 4 pints (1.89 L)
  • Wing transport protection: Wing transport locks | Skid shoes - Wing deck: 1 replaceable per wing / Center deck: 2 replaceable shoes | Blade rotation Left wing: Counterclockwise / Center deck: Counterclockwise / Right wing: Clockwise | Blade bolt: Keyed with hardened flat washer and locknut | Front & rear guards: Single chain | Transport axle: Spring-cushioned lift cylinder
  • Hitch: 793 lbs (359.7 kg) | Machine: 2,540 lbs (1152.1 kg)
  • 10 Gauge (3.4 mm) deck
  • Side skirt: 3/16" (5 mm) Plate
  • Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.